BLE 3 Click Board™

Product Code: MIKROE-2471

Built-In RTC Daves Energy One of the standout features of the NINA-B1 module is its real time counter functionality. This counter can be used to generate precisely timed BLE advertising events (broadcasting packets to every device around), without involving the main MCU. The RTC can be operated in standby mode as well — further lowering the already low power consumption. Designed for IoT and Smart Devices BLE – also known as Bluetooth Low Energy is designed for sensors and smart devices that send out small pieces of information in regular intervals and need to have very low power consumption. For example our Hexiwear uses BLE for wireless communication. You can combine the BLE 3 Click Board™ with one of our sensor clicks, like the Air quality click, and get notified what the air quality of your home or office is all the time. Power Saving Modes For really low power consumption there are different power saving modes to conserve battery life – standby mode and power off mode. The module can spend most of the time in power off mode and wake up periodically only to send small packages of data.

The ADC featured on the BLE 3 Click Board™ can sample up to 200 kHz using different inputs as sample triggers and it supports 8/10/12-bit resolution. For applications that require it, u-blox offers Apple iOS and Google Android connectivity. The BLE 3 Click Board™ communicates with the target board MCU through the UART, SPI and I2C interface, with the addition of 7 GPIO pins. It uses 3.3V power supply only. SPECIFICATIONS Type BT/BLE Applications Medical equipment and fitness applications, IoT devices, home automation, smart energy, etc. On-board modules NINA-B1 Bluetooth 4.2 module Key Features LED indicates power is on, Antenna power +10dBm, 2.4 GHz frequency band Interface GPIO,I2C,SPI,UART Compatibility mikroBUS Click board size M (42.9 x 25.4 mm) Input Voltage 3.3V Display Also known as Bluetooth Low Energy, BLE is intended for small smart devices like home automation sensor and fitness applications that need to have really low power consumption and long battery life. The BLE 3 Click Board™ communicates with the target board MCU through the UART, SPI and I2C interface, with the addition of 7 GPIO pins. It uses 3.3V power supply only. The NINA-B1 module has different power saving modes to conserve battery life – standby mode and power off mode. The module usually spends most of the time in power off mode (it is the primary mode) and wakes up to send small packages of data, and then powers off again. The following events can be used to bring the module out of standby-mode: External wake-up event RTC event Analog or digital sensor event (programmable voltage level or edge detection) During standby mode, the module is clocked at 32 kHz reference clock, which is generated by an internal 32 kHz oscillator. The module is fully Bluetooth qualified and provides global modular approval. The ADC can sample up to 200 kHz using different inputs as sample triggers and it supports 8/10/12 bit resolution. Any of the 8 analog inputs can be used both as single-ended inputs and as differential pairs for measuring the voltage across them. The ADC supports full 0 V to VCC input range. The NINA-B112 modules have an integrated antenna mounted on the PCB (10.0 x 14.0 mm). The RF signal pin is not connected to any signal path. You can configure NINA-B1 modules through U-Blox S-Center toolbox software using AT commands. The s-center evaluation software is available free of charge and can be downloaded from the U-Blox website. PINOUT DIAGRAM This table shows how the pinout on the BLE 3 Click Board™ ccorresponds to the pinout on the mikroBUS™ socket (the latter shown in the two middle columns). Notes Pin Pin Notes NC 1 AN PWM 16 NC Active-high Reset pin RST 2 RST INT 15 RTS UART request to send UART clear to send CS/CTS 3 CS RX 14 TX SPI0 SCLK 4 SCK TX 13 RX SPI0 MISO 5 MISO SCL 12 SCL SPI0 MOSI 6 MOSI SDA 11 SDA